...
BYTE | BIT RANGE | SIZE | OFFSET | ABBREVIATION | DETAILS | |
1 | DB0.7…0.0 | 8 | 0 | FADD | Flow Raw Value Offset With 2’s complement Default = 0x00 = 0.00°C Res Resolution = 0.25°C | |
0x00 | 0.00 | |||||
0x01 | 0.25 | |||||
0x02 | 0.50 | |||||
… | … | |||||
0x7F | 31.75 | |||||
0x80 | -32.00 | |||||
… | … | |||||
0xFF | -0.25 | |||||
2 | DB1.7…1.0 | 8 | 8 | FMUL | Flow Raw Value Multiplication Default = 0x64 = 1.00°C Res = 0.01°C | |
3 | DB2.7…2.0 | 8 | 16 | NFD | Number of most recent Flow Raw Temperature values to delay by (skip) Default = 0 Clamped to [0..=20] | |
4 | DB3.7…3.0 | 8 | 24 | NMAF | Number of values used in calculation of Flow Moving Average Default = 6 Clamped to [1..=20] | |
5 | DB4.7…4.0 | 8 | 32 | NMAA | Number of values used in calculation of Ambient Moving Average Default = 1 Clamped to [1..=20] | |
6 | DB5.7…5.0 | 8 | 40 | NMAE | Number of values used in calculation of Estimate Moving Average Default = 1 Clamped to [1..=20] | |
7 | DB6.7…6.0 | 8 | 48 | RATO | Ratio Offset Default = 0 Res = 0.01 | |
8 | DB7.7…7.0 | 856 | POW | Ratio Power Default = 0x00 = 1.2 Res = 0.01 | ||
To receive an Uplink without changing any settings, send an empty Downlink.
...
Same a Downlink, confirming settings.
Ambient Temperature Estimate Calculation:
| Mathblock | ||||
|---|---|---|---|---|
| ||||
--uriencoded--\ |
...
begin%7Balign*%7D & \text%7BFlow Smoothened |
...
%7D F_s = \ |
...
Recommended Settings
...
Scenario
...
Flow Offset
...
Flow Multiplication
...
Flow Delay
...
Flow Moving Average
...
Estimate Moving Average
...
Ratio Power
...
Small or well-insulated room
...
0.0
...
1.0
...
0 or 1
If > 0, reduce PI-Coefficient KP (see Port 7)
...
1.0 + small
...
Large or poorly-insulated room
...
0.0
...
1.0
...
Consider using
If > 0, reduce PI-Coefficient KP (see Port 7)
...
1.0 + big
...
Unheated Room is warm
...
0.0
...
1.0
...
1.0 + small
...
Unheated Room is cold
...
0.0
...
1.0
...
1.0 + big
...
Temperature close to the radiator is desired
...
0.0
...
1.0
...
1.0 + small
...
Temperature far from the radiator is desired
...
0.0
...
1.0
...
1.0 + big
...
Flow Temperature fluctuates
...
0.0
...
1.0
...
Use to smooth
...
Estimated Temperature fluctuates
...
0.0
...
1.0
...
Use to smooth
...
Device is mounted above an exposed pipe
...
Use to compensate
...
frac %7B(0.2 F + 1.2F_%7Bt-1%7D + 1F_%7Bt-2%7D + 0.8F_%7Bt-3%7D + 0.6F_%7Bt-4%7D + 0.3F_%7Bt-5%7D + 0.1F_%7Bt-6%7D) %7D %7B4.2%7D + \text%7BFlow Offset%7D
\\
\\
& \text%7Bwhere F = Flow Raw Value%7D
\\
& \text%7Bwhere Flow Offset = 0 (default)%7D
\\
\\
& \text%7Bif %7D \Big(F_s - z \big( F_s - 0.5(F_%7Bs_%7Bt-3%7D%7D + F_%7Bs_%7Bt-4%7D%7D ) \big) \Big) < \text%7B Ambient Raw Value%7D
\\
& \text%7Bthen%7D
\\
& \hspace%7B1cm%7D \text%7BFlow Corrected %7D F_c = \text%7BAmbient Raw Value%7D
\\
& \text%7Belse%7D
\\
& \hspace%7B1cm%7D \text%7BFlow Corrected %7D F_c = \Big(F_s - z * \big( F_s - 0.5(F_%7Bs_%7Bt-3%7D%7D + F_%7Bs_%7Bt-4%7D%7D ) \big) \Big)
\\
\\
& \text%7Bwhere z = 0.1%7D
\\
\\
& \textbf%7BAmbient Temperature Estimate%7D = \textbf%7BAmbient Raw Value%7D * \Bigg( \frac%7B\textbf%7BAmbient Raw Value%7D%7D%7B\textbf%7BFlow Corrected %7D F_c%7D \Bigg) %5e%7B1.2%7D
\end%7Balign*%7D
|